Environmental impact assessment of the electrokinetic adsorption barriers to remove different herbicides from agricultural soils.

In this study, the sustainability of the electrokinetic remediation soil flushing (EKSFs) process integrated without and with adsorption barriers (EKABs) have been evaluated for the treatment of four soils contaminated with Atrazine, Oxyfluorfen, Chlorosulfuron and 2,4-D. To this purpose, the environmental effects of both procedures (EKSFs and EKABs) have been determined through a life cycle assessment (LCA). SimaPro 9.3.0.3 was used as software tool and Ecoinvent 3.3 as data base to carry out the inventory of the equipment of each remediation setup based on experimental measurements. The environmental burden was quantified using the AWARE, USEtox, IPPC, and ReCiPe methods into 3 Endpoint impact categories (and damage to human health, ecosystem and resources) and 7 Midpoints impact categories (water footprint, global warming potential, ozone depletion, human toxicity (cancer and human non-cancer), freshwater ecotoxicity and terrestrial ecotoxicity). In general terms, the energy applied to treatment (using the Spanish energy mix) was the parameter with the greatest influence on the carbon footprint, ozone layer depletion and water footprint accounting for around 70 % of the overall impact contribution. On the other hand, from the point of view of human toxicity and freshwater ecotoxicity of soil treatments with 32 mg kg-1 of the different pesticides, the EKSF treatment is recommended for soils with Chlorosulfuron. In this case, the carbon footprint and water footprint reached values around 0.36 kg of CO2 and 114 L of water per kg of dry soil, respectively. Finally, a sensitivity analysis was performed assuming different scenarios.

Penicillium oxalicum SL2-enhanced nanoscale zero-valent iron effectively reduces Cr(VI) and shifts soil microbiota.

Most current researches focus solely on reducing soil chromium availability. It is difficult to reduce soil Cr(VI) concentration below 5.0 mg kg-1 using single remediation technology. This study introduced a sustainable soil Cr(VI) reduction and stabilization system, Penicillium oxalicum SL2-nanoscale zero-valent iron (nZVI), and investigated its effect on Cr(VI) reduction efficiency and microbial ecology. Results showed that P. oxalicum SL2-nZVI effectively reduced soil total Cr(VI) concentration from 187.1 to 3.4 mg kg-1 within 180 d, and remained relatively stable at 360 d. The growth curve of P. oxalicum SL2 and microbial community results indicated that γ-ray irradiation shortened the adaptation time of P. oxalicum SL2 and facilitated its colonization in soil. P. oxalicum SL2 colonization activated nZVI and its derivatives, and increased soil iron bioavailability. After restoration, the negative effect of Cr(VI) on soil microorganisms was markedly alleviated. Cr(VI), Fe(II), bioavailable Cr/Fe, Eh, EC and urease (SUE) were the key environmental factors of soil microbiota. Notably, Penicillium significantly stimulated the growth of urease-positive bacteria, Arthrobacter, Pseudarthrobacter, and Microvirga, synergistically reducing soil chromium availability. The combination of P. oxalicum SL2 and nZVI is expected to form a green, economical and long-lasting Cr(VI) reduction stabilization strategy.

Hydrogen Nanobubbles Generated In Situ from Nanoscale Zerovalent Iron with Water to Further Enhance Selenite Sequestration.

Gas nanobubbles used for water treatment and recovery give rise to great concern for their unique advantages of less byproducts, higher efficiency, and environmental friendliness. Nanoscale zerovalent iron (nZVI), which has also been widely explored in the field of environmental remediation, can generate gas hydrogen by direct reaction with water. Whether nanoscale hydrogen bubbles can be produced to enhance the pollution removal of the nZVI system is one significant concern involved. Herein, we report direct observations of in situ generation of hydrogen nanobubbles (HNBs) from nZVI in water. More importantly, the formed HNBs can enhance indeed the reduction of Se(IV) beyond the chemical reduction ascribed to Fe(0), especially in the anaerobic environment. The possible mechanism is that HNBs enhance the reducibility of the system and promote electron transport in the solution. This study demonstrates a unique function of HNBs combined with nZVI for the pollutant removal and a new approach for in situ HNB generation for potential applications in the fields of in situ remediation agriculture, biotechnology, medical treatment, health, etc.

Sustainable remediation of Cr(VI)-contaminated soil by soil washing and subsequent recovery of washing agents using biochar supported nanoscale zero-valent iron.

Soil contamination by Cr(VI) has attracted widespread attention globally in recent years, but it remains a significant challenge in developing an environmentally friendly and eco-sustainable technique for the disposal of Cr(VI)-contaminated soil. Herein, a sustainable cyclic soil washing system for Cr(VI)-polluted soil remediation and the recovery of washing agents using biochar supported nanoscale zero-valent iron (nZVI-BC) was established. Citric acid (CA) was initially screened to desorb Cr(VI) from contaminated soil, mobilizing Cr from the highly bioaccessible fractions. The nZVI-BC exhibited superior properties for Cr(VI) and Cr(total) removal from spent effluent, allowing effective recovery of the washing agents. The elimination mechanism of Cr(total) by nZVI-BC involved the coordinated actions of electrostatic adsorption, reduction, and co-precipitation. The contributions to Cr(VI) reduction by Fe0, surface-bound Fe(II), and soluble Fe(II) were 0.6 %, 39.8 %, and 59.6 %, respectively. Meanwhile, CA favored the activity of surface-bound Fe(II) and Fe0 in nZVI-BC, enhancing the production of soluble Fe(II) to strengthen Cr(VI) removal. Finally, the recovered washing agent was proven to be reused three times. This study showcases that the combined soil washing using biodegradable chelant CA and effluent treatment by nZVI-BC could be a sustainable and promising strategy for Cr(VI)-contaminated soil remediation.

Remediation of cadmium-contaminated soil: GLDA-assisted extraction and sequential FeCl3-CaO-based post-stabilization.

Cadmium (Cd) contamination of farmland soils is a growing concern because of its highly toxic impact on ecosystems and human health. Chelator-assisted washing and chemical immobilization are effective remediation strategies for Cd-contaminated soils. Ethylenediaminetetraacetic acid (EDTA) has traditionally been used for soil washing, but its persistence in the environment and subsequent toxicity have raised significant ecological concerns. Consequently, biodegradable chelators have gained increasing attention as eco-friendly alternatives to the persistent chelator, EDTA. Therefore, this study evaluated the performance and efficacy of three biodegradable chelators: L-glutamate-N,N'-diacetic acid (GLDA), methylglycine-diacetic acid (MGDA), and 3-hydroxy-2,2'-iminodisuccinic acid (HIDS) in comparison to EDTA for remediating a real Cd-contaminated agricultural soil. The influence of treatment parameters, including chelator variants, washing time, chelator concentration, solution pH, and liquid-to-soil ratio (L/S) on Cd extraction was studied and optimized to attain the maximum removal rate. Following chelator-assisted washing, the efficacy of a stabilization preference combining FeCl3 and CaO in reducing the leaching potential of residual Cd in chelator-washed soil residues was also investigated. GLDA demonstrated comparable Cd extraction efficiency to EDTA, and the Cd extraction efficiency was found to be positively correlated with the soil washing parameters. However, under the optimized conditions (chelator concentration: 10 mmol L-1; washing time: 3 h; solution pH: 3; L/S ratio: 10:1), GLDA exhibited a higher Cd extraction rate than EDTA or the other chelators. Furthermore, a post-treatment process incorporating FeCl3 and CaO substantially diminished the water-leachable Cd content in the resultant soil residues. The proposed remediation strategy, which combines chemically assisted washing and stabilization, could be a practical option for extracting bulk Cd from soil and reducing the leaching potential of residual Cd.

Remobilization of Cd caused by iron oxide phase transformation and Mn2+ competition after stabilization by nano zero valent iron.

Stabilization techniques are vital in controlling Cd soil pollution. Nano zero valent iron (nZVI) has been extensively utilized for Cd remediation owing to its robust adsorption and reactivity. However, the environmental stress-induced stability of Cd after nZVI addition remains unclear. A pot experiment was conducted to evaluate the Cd bioavailability in continuously flooded (130 d) soil after stabilization with nZVI. The findings indicated that nZVI application did not result in a decline in Cd concentration in rice, as compared to the no-nZVI control. Additionally, nZVI simultaneously increased the available Cd concentration, iron-manganese oxide-bound (OX) Mn fraction, and relative abundance of Fe(III)-reducing bacteria, but it decreased OX-Cd and Mn availability in soil. Cadmium in rice tissues was positively correlated with the available Cd in soil. The results of subsequent adsorption tests demonstrated that CdO was the product of Cd adsorption by the nZVI aging products. Conversely, Mn2+ decreased the adsorption capacity of Cd-containing solutions. These results underscore the crucial role of both biotic and abiotic factors in undermining the stabilization of nZVI under continuous flooding conditions. This study offers novel insights into the regulation of nZVI-mediated Cd stabilization efficiency in conjunction with biological inhibitors and functional modification techniques.

Study on remediation of cadmium contaminated paddy field by ramie (Boehmeria nivea L.) floating island and its supporting technology.

Ramie (Boehmeria nivea L.) is an ideal crop for cadmium (Cd) pollution remediation due to its advantages of both remediating and utilizing, however, it is mainly carried out in dry land, whose restoration effect is relatively slow. Previously, we found that the ramie plants cultivated by hydroponics has several tens of times higher Cd absorption capacity than that planted in soil. However, the issue of how to use hydroponic ramie to remediate Cd contaminated paddy fields needs to be addressed. In this study, we innovatively developed the ramie floating island technology and studied its remediation model on simulated Cd contaminated paddy fields. Different ramie varieties were used to compare the remediation effects, and the results showed that there were differences in adaptability among different varieties on floating islands and the remediation ability of the tested ramie varieties was Z2 > Z1 > Z3. Different harvested times were set to analyze the effects of harvested model on remediation, and it was suggested that multiple harvests can be carried out according to the plant growth status of ramie floating island after 30 days of remediation to achieve better remediation effects. Low water level height (5 cm) of paddy field was beneficial for the accumulation of Cd in the roots, but considering the adaptability of various ramie varieties and the effect of long-term restoration, it was recommended that the water level height of 20 cm for the cultivation of ramie floating island was more suitable. Moreover, we found that low concentration of citric acid (≤2 g L-1) or polyaspartic acid (≤3 g L-1) can improve the remediation effects for ramie floating island. Our study opens up a novel approach for ramie to remediate heavy metal pollution and provides a technical reference for water body Cd remediation by plants.

Application and development of zero-valent iron (ZVI)-based materials for environmental remediation: A scientometric and visualization analysis.

Zero-valent iron (ZVI)-based materials are among the most widely used engineered particles in the field of environmental remediation. To provide a comprehensive overview of the status and trend of the research on them, this study conducted a quantitative and visual analysis of 6296 relevant publications obtained from Web of Science between 1994 and 2022 using CiteSpace software. By using the bibliometric method, this work systematically analyzed the knowledge structure, research hotspots and trends of ZVI-based materials in this field. The results show that the research on ZVI-based materials in this field developed rapidly over the past 28 years. China is the greatest contributor with the most published articles and collaborations. Still, the USA has the most academic influence with the highest average citations per article. Chinese Academy of Sciences and Tongji University are the primary establishments that produced the greatest number of publications and had the highest h-index. Keyword cluster analysis indicates that the primary research topics are related to reductive dechlorination, sulfate radical, arsenic removal, graphene oxide, porous media, peroxymonosulfate, groundwater remediation, and permeable reactive barrier. Meanwhile, keyword burst analysis reveals that the primary research hotspots and frontiers of ZVI focus on its modification, the refractory and emerging contaminants treatment, persulfate activation, and electron transfer. However, no keywords or topics related to the environmental impact and toxicity of ZVI-based materials are available in the keyword clustering and burst analysis results, indicating this direction deserves more attention in future research. Through a comprehensive and in-depth bibliometric analysis, this paper provides new insight into the research hotspots and development trends of the research on ZVI-based materials in environmental remediation.

Insects and spiders on Acacia mangium (Fabaceae) saplings as bioindicators for the recovery of tropical degraded areas / Insetos e aranhas em plantas de Acacia mangium (Fabaceae) como bioindicadores na recuperação de área tropical degradada

Abstract Acacia mangium is a pioneer species with fast growth and frequently used in the recovery of degraded areas. The objectives were to evaluate insects and spiders, their ecological indices and interactions on A. mangium saplings in a tropical degraded area in recovering process. The experimental design was completely randomized with 24 replications, with treatments represented by the first and second years after A. mangium seedling planted. Numbers of leaves/branch, branches/sapling, and ground cover by A. mangium saplings, Hemiptera: Phenacoccus sp. and Pachycoris torridus; Hymenoptera: Tetragonisca angustula and Trigona spinipes, Brachymyrmex sp., Camponotus sp. and Cephalotes sp.; Blattodea: Nasutitermes sp. and Neuroptera: Chrysoperla sp.; abundance, species richness of pollinating insects, tending ants, and the abundance of Sternorrhyncha predators were greatest in the second year after planting. Numbers of Hemiptera: Aethalium reticulatum, Hymenoptera: Camponotus sp., Cephalotes sp., Polybia sp., T. angustula, T. spinipes, tending ants, pollinating insects, Sternorrhyncha predators and species richness of tending ants were highest on A. mangium saplings with greatest numbers of leaves or branches. The increase in the population of arthropods with ground cover by A. mangium saplings age increase indicates the positive impact by this plant on the recovery process of degraded areas.

Resumo Acacia mangium é uma espécie pioneira, de rápido crescimento e utilizada na recuperação de áreas degradadas. Os objetivos foram avaliar insetos e aranhas, seus índices ecológicos e interações com plantas de A. mangium em área tropical degradada em processo de recuperação. O delineamento experimental foi inteiramente casualizado com 24 repetições, com os tratamentos representados pelos primeiro e segundo anos após a plantio de A. mangium. Os números de folhas/galhos, galhos/plantas e cobertura do solo por plantas de A. mangium, de Hemiptera: Phenacoccus sp. e Pachycoris torridus; Hymenoptera: Tetragonisca angustula e Trigona spinipes, Brachymyrmex sp., Camponotus sp. e Cephalotes sp.; Blattodea: Nasutitermes sp. e Neuroptera: Chrysoperla sp.; a abundância, riqueza de espécies de insetos polinizadores, formigas cuidadoras e a abundância de predadores de Sternorrhyncha foram maiores no segundo ano após o plantio. Os números de Hemiptera: Aethalium reticulatum, Hymenoptera: Camponotus sp., Cephalotes sp., Polybia sp., T. angustula, T. spinipes, formigas cuidadoras, insetos polinizadores, predadores de Sternorrhyncha e a riqueza de espécies de formigas cuidadoras foram maiores em plantas de A. mangium com maior altura e número de folhas ou galhos. O aumento populacional de artrópodes e da cobertura do solo com o processo de envelhecimento das plantas de A. mangium indicam impacto positivo dessa planta na recuperação de áreas degradadas.

Selectively Positioned Catechol Moiety Supports Ultrashort Self-Assembling Peptide Hydrogel Adhesion for Coral Restoration.

Coral reef survival is threatened globally. One way to restore this delicate ecosystem is to enhance coral growth by the controlled propagation of coral fragments. To be sustainable, this technique requires the use of biocompatible underwater adhesives. Hydrogels based on rationally designed ultrashort self-assembling peptides (USP) are of great interest for various biological and environmental applications, due to their biocompatibility and tunable mechanical properties. Implementing superior adhesion properties to the USP hydrogel compounds is crucial in both water and high ionic strength solutions and is relevant in medical and marine environmental applications such as coral regeneration. Some marine animals secrete large quantities of the aminoacids dopa and lysine to enhance their adhesion to wet surfaces. Therefore, the addition of catechol moieties to the USP sequence containing lysine (IIZK) should improve the adhesive properties of USP hydrogels. However, it is challenging to place the catechol moiety (Do) within the USP sequence at an optimal position without compromising the hydrogel self-assembly process and mechanical properties. Here, we demonstrate that, among three USP hydrogels, DoIIZK is the least adhesive and that the adhesiveness of the IIZDoK hydrogel is compromised by its poor mechanical properties. The best adhesion outcome was achieved using the IIZKDo hydrogel, the only one to show equally sound adhesive and mechanical properties. A mechanistic understanding of this outcome is presented here. This property was confirmed by the successful gluing of coral fragments by means of IIZKDo hydrogel that are still thriving after more than three years since the deployment. The validated biocompatibility of this underwater hydrogel glue suggests that it could be advantageously implemented for other applications, such as surgical interventions.

Reserve mobilization and secondary metabolites during seed germination and seedling establishment of the tree Erythrina velutina (Fabaceae) / Movilización de reservas y metabolitos secundarios durante la germinación de semillas y el establecimiento de plántulas del árbol Erythrina velutina (Fabaceae)

Introduction: The lack of knowledge on seed germination and seedling establishment is a main constraint for the restoration of degraded areas, including the tropical dry forest known as Caatinga. Objective: To assess reserve and secondary metabolite mobilization during seed germination and seedling establishment in Erythina velutina. Methods: We scarified, disinfected, imbibed, sown between towel paper, and incubated seeds under controlled conditions. We hydroponically cultivated seedlings in a greenhouse. We harvested cotyledons at seed imbibition, radicle protrusion, hypocotyl emergence, apical hook formation and expansion of cordiform leaves, first trifoliate leaf, and second trifoliate leaf. Results: Seeds contained approximately 20 % starch, 14.5 % storage proteins, 11.6 % neutral lipids, and 5.7 % non-reducing sugars on a dry weight basis. Soluble sugars were mainly consumed from hypocotyl emergence to apical hook formation, while major reserves were mobilized from apical hook formation to expansion of first trifoliate leaf. Enzymatic activity increased from mid to late seedling establishment, causing the mobilization of starch, oils, and proteins. Terpenoid-derivatives, flavonoids, phenolic acids, and alkaloids were detected. Flavonoids and phenolic acids were present at almost all stages and terpenoid-derivatives disappeared at expansion of cordiform leaves. Conclusion: Soluble sugars support early seedling growth, while starch, oils and proteins are simultaneously mobilized from mid to late establishment by amylases, lipases, and acid proteases. The cotyledons contain secondary metabolites, which may act in seedling defense. High content of reserves and presence of secondary metabolites in the cotyledons could enable E. velutina seedlings endure stress, validating their use in the restoration of degraded areas.

Introducción: La falta de conocimiento sobre la germinación de semillas y el establecimiento de plántulas es una de las principales limitaciones para la restauración de áreas degradadas, incluido el bosque seco tropical conocido como Caatinga. Objetivo: Evaluar la movilización de reservas y metabolitos secundarios durante estas etapas de desarrollo en Erythina velutina. Métodos: Las semillas fueron escarificadas, desinfectadas, embebidas, sembradas entre toallas de papel e incubadas bajo condiciones controladas. Cultivamos las plántulas hidropónicamente en un invernadero. Recolectamos los cotiledones en la imbibición de la semilla, la protrusión de la radícula, la emergencia del hipocótilo, la formación del gancho apical y la expansión de las hojas cordiformes, la primera y segunda hoja trifoliada. Resultados: Las semillas contenían 20 % de almidón, 14.5 % de proteínas de almacenamiento, 11.6 % de lípidos neutros y 5.7 % de azúcares no reductores en peso seco. Los azúcares solubles se consumieron desde la emergencia del hipocótilo hasta la formación del gancho apical. Las principales reservas se movilizaron desde la formación del gancho apical hasta la expansión de la primera hoja trifoliada. La actividad enzimática aumentó desde la mitad hasta el final del establecimiento de las plántulas, movilizando almidón, aceites y proteínas. Se detectaron derivados de terpenoides, flavonoides, ácidos fenólicos y alcaloides. Los flavonoides y los ácidos fenólicos estuvieron en casi todas las etapas y los derivados terpenoides desaparecieron en la expansión de las hojas cordiformes. Conclusión: Los azúcares solubles apoyan el crecimiento temprano de las plántulas; el almidón, los aceites y las proteínas se movilizan simultáneamente desde el establecimiento medio hasta el final por amilasas, lipasas y proteasas ácidas. Los cotiledones contienen metabolitos secundarios, que pueden actuar en la defensa de las plántulas. El alto contenido de reservas y los metabolitos secundarios en los cotiledones podría permitir que las plántulas de E. velutina toleren estrés, validando su uso en la restauración de áreas degradadas.

Potential applications of green-synthesized iron oxide NPs for environmental remediation.

Water pollution is a significant issue worldwide due to an increase in anthropogenic activities. Heavy metals and dyes are among the most problematic contaminants that threaten the environment and negatively impact human health. Iron oxide nanoparticles (IONPs) synthesized using green methods have shown potential in these areas due to their significant adsorption capacity and photocatalytic potential. The size and morphology of biogenic IONPs can be tailored depending upon the concentration of the reducing medium and metal salt precursor. Green-synthesized IONPs have been found to be effective, economical, and environmentally friendly with their large surface area, making them suitable for removing toxic matter from contaminated water. Furthermore, they exhibit antibacterial potential against harmful microorganisms. The study emphasizes the importance of using such environmentally friendly tools to remove heavy metal ions and organic compounds from contaminated water. The underlying mechanism for the adsorption of heavy metal ions, photocatalytic degradation of organic compounds, and antimicrobial action has been explored in detail. The future prospective for the beneficial utilization of biogenic IONPs has also been signified to provide a detailed overview.

Sulfidated nanoscale zero valent iron for in situ immobilization of hexavalent chromium in soil and response of indigenous microbes.

This study aimed to investigate the immobilization efficiency of sulfidated nanoscale zero valent iron on Cr(VI) in soil. Reactions between sulfidated nanoscale zero valent iron and Cr(VI) in soil system and effects of sulfidated nanoscale zero valent iron on microbes had been demonstrated. Solid characterization results confirmed the incorporation of sulfur into nanoscale zero valent iron. Furthermore, the main oxidation products of iron after the reactions were magnetite, goethite and lepidocrocite. Fe-Cr complexes indicated that Cr(VI) was reduced to Cr(III). The results of 16 S rRNA gene analysis indicated that the sulfidated nanoscale zero valent iron had a limited bactericidal effect but further stimulated the sulfite reductase gene population, representing its positive effect for the soil remediation. The study showed that some microflora such as Protobacteria were promoted, while others community such as Firmicutes, were depressed. Furthermore, Cr mainly converted from a high toxic state such as exchangeable (EX) to less bioavailable state such as iron-manganese oxides bound (OX) and organic matter-bound (OM), thus reducing the toxicity of Cr when sulfidated nanoscale zero valent iron was added. High immobilization efficiency of the Cr(VI) compared to nanoscale zero valent iron indicated an improvement on selectivity and reactivity after sulfidation. Overall, sulfidated nanoscale zero valent iron was promising for the immobilization of Cr(VI) immobilization soil.

Immobilization of cadmium in river sediments by different modified nanoscale zero-valent iron: performance, mechanisms, and Fe dissolution.

Modified nanoscale zero-valent iron (NZVI) exhibited great potential for the remediation of heavy metal contaminated river sediments, but its mechanisms and environmental risks are still unclear. This study systematically discussed the performance and the mechanisms of modified NZVI materials, i.e., sodium alginate-coated NZVI (SNZVI), rhamnolipid-coated NZVI (RNZVI), and graphene oxide-loaded NZVI (GNZVI), for the stabilization of Cd in sediment, with the exploration of their stability to Cd at various pH values and Fe dissolution rate. Compared with the control, the toxicity characteristic leaching procedure (TCLP) leachable Cd decreased by 52.66-96.28%, and the physiologically based extraction test (PBET) extractable Cd decreased by 44.68-70.21% after 56 days of incubation with the immobilization efficiency varying according to GNZVI > RNZVI > SNZVI > NZVI. Besides, the adsorption behavior of Cd on materials was fitted with the Freundlich model and classified as an endothermic, spontaneous, and chemical adsorption process. SEM-EDX, XRD, and FTIR results verified that the stabilization mechanisms of Cd were principally based on the adsorption, complexation of Cd2+ with secondary Fe minerals (including Fe2O3, γ-Fe2O3, and γ-FeOOH) and precipitation (Cd(OH)2). From the risk assessment results, it was observed that the materials were favorable for Cd stabilization at a pH range from 7 to 11, meanwhile, the leaching concentration of Fe in the overlying water was detected below the limit value. These findings pave the way to developing an effective strategy to remediate Cd contaminated river sediments.

Coupling electrokinetic remediation with flushing using green tea synthesized nano zero-valent iron/nickel to remediate Cr (VI).

This study focuses on a flushing-electrokinetic remediation technology of hexavalent chromium from the chromium slag dump site. A suspension of nanoscale zero-valent iron/nickel fabricated from green tea (GT-nZVI/Ni), was employed as an eluent to degrade Cr (VI) and enhance the remediation effectiveness of a single EK. The removal efficiency of Cr (VI) was compared under different voltages, electrode spacings and pH values of the anolyte. The results demonstrated that the combined flushing and EK achieved a removal rate of Cr (VI) in the soil throughout all the experiments ranging from 83.08 to 96.97% after 120 h. The optimal result was obtained when the voltage was 28 V, the pH value of anolyte was 3 and the electrode spacing was 15 cm. The removal of Cr (VI) reached 91.49% and the energy consumption was 0.32606 kW·h·g-1. The underlying mechanisms responsible for the removal of Cr (VI) by GT-nZVI/Ni flushing-EK primarily involved electromigration, reduction and adsorption co-precipitation processes. The fractionation analysis of Cr (VI) concentration in the soil after remediation showed that the presence of GT-nZVI/Ni facilitated the conversion of Cr (VI) into oxidizable and residual states with low mobility and toxicity. The results of toxicity characteristic leaching procedure (TCLP) indicated that the leaching concentration of Cr (VI) was below 1 mg·L-1, complying with the standards set by the Environmental Protection Agency. Additionally, the phytotoxicity testing revealed that the germination index (GI) of the remediated soil reached 54.75%, indicating no potential harm to plants.

Accelerated electron and mass transfer through constructing H2WO4/Ti3C2/g-C3N4 Z-scheme photocatalyst for environmental remediation.

The catalytic efficiency of photocatalysts highly depends on electron transport and mass transfer. Herein, we designed and prepared an effective H2WO4/Ti3C2/g-C3N4 (HTC) Z-scheme heterojunction through interfacial engineering strategy. The results manifested that 97.4% of Cr(VI) (80 µM, 50 mL) could be removed by HTC heterojunction within 10 min under visible light irradiation. The reduction rate constant of Cr(VI) for H2WO4/g-C3N4 (HC) heterojunction increased by a factor of 21 after introducing the conductive Ti3C2. Moreover, 96% of tetracycline (TC, 10 mg L-1, 50 mL) could be degraded by HTC heterojunction within 30 min. The electronic conductivity and ionic diffusion coefficient of HC heterojunction increased by a factor of 64 and 1064 after adding Ti3C2, respectively. This result indicated that the introduction of highly conductive Ti3C2 significantly improved the electron and mass transfer of the heterojunction. Meanwhile, the HCT heterojunction displayed favorable photocurrent, and keep excellent photostability during the long-term test. Moreover, density functional theory (DFT) calculations demonstrated that the internal electric field (IEF) from g-C3N4 to H2WO4 in HCT heterojunction promotes the combination of the photoinduced electrons in the H2WO4 conduction band (CB) with photoinduced holes in the g-C3N4 valence band (VB), thus accelerating the charge transfer in the HCT Z-scheme heterojunction. The antibacterial efficiency of HTC heterojunction against E. coli and S. aureus could reach up to 98.4% and 99.7%, respectively. The degradation intermediates and the potential degradation mechanism of TC were analyzed and proposed based on the results of HPLC-MS analysis. Moreover, the toxicity of TC and degradation intermediates were estimated by Toxicity Estimation Software (T.E.S.T.) based on quantitative structure-activity relationship (QSAR). This work provided a valuable guideline for designing the effective MXene-based Z-scheme heterojunction for environmental remediation.

Covalent organic frameworks as highly versatile materials for the removal and electrochemical sensing of organic pollutants.

The presence of persistent organic compounds in water has become a worldwide issue due to its resistance to natural degradation, inducing its environmental resilience. Therefore, the accumulation in water bodies, soils, and humans produces toxic effects. Also, low levels of organic pollutants can lead to serious human health issues, such as cancer, chronic diseases, thyroid complications, immune system suppression, etc. Therefore, developing efficient and economically viable remediation strategies motivates researchers to delve into novel domains within material science. Moreover, finding approaches to detect pollutants in drinking water systems is vital for safeguarding water safety and security. Covalent organic frameworks (COFs) are valuable materials constructed through strong covalent interactions between blocked monomers. These materials have tremendous potential in removing and detecting persistent organic pollutants due to their high adsorption capacity, large surface area, tunable porosity, porous structure, and recyclability. This review discusses various synthesis routes for constructing non-functionalized and functionalized COFs and their application in the remediation and electrochemical sensing of persistent organic compounds from contaminated water sources. The development of COF-based materials has some major challenges that need to be addressed for their suitability in the industrial configuration. This review also aims to highlight the importance of COFs in the environmental remediation application with detailed scrutiny of their challenges and outcomes in the current research scenario.

Microbial remediation of oil-contaminated shorelines: a review.

Frequent marine oil spills have led to increasingly serious oil pollution along shorelines. Microbial remediation has become a research hotspot of intertidal oil pollution remediation because of its high efficiency, low cost, environmental friendliness, and simple operation. Many microorganisms are able to convert oil pollutants into non-toxic substances through their growth and metabolism. Microorganisms use enzymes' catalytic activities to degrade oil pollutants. However, microbial remediation efficiency is affected by the properties of the oil pollutants, microbial community, and environmental conditions. Feasible field microbial remediation technologies for oil spill pollution in the shorelines mainly include the addition of high-efficiency oil degrading bacteria (immobilized bacteria), nutrients, biosurfactants, and enzymes. Limitations to the field application of microbial remediation technology mainly include slow start-up, rapid failure, long remediation time, and uncontrolled environmental impact. Improving the environmental adaptability of microbial remediation technology and developing sustainable microbial remediation technology will be the focus of future research. The feasibility of microbial remediation techniques should also be evaluated comprehensively.

Coal gangue-based magnetic porous material for simultaneous remediation of arsenic and cadmium in contaminated soils: Performance and mechanisms.

Remediation of arsenic (As) and cadmium (Cd) co-contaminated soil is a challenge in environmental remediation. In this study, coal gangue-based magnetic porous material (MPCG) was designed for simultaneous immobilization of As and Cd in contaminated soil. After the incubation experiment, the effects of CG and MPCG on the availability and fractions of As and Cd and the related microbial functional genes were analyzed to explore the potential remediation mechanisms of MPCG for As and Cd in contaminated soil. The results showed that the stabilization effect of MPCG on As and Cd was significantly higher than that of coal gangue. It reduced the available As and Cd by 17.94-29.81% and 14.22-30.41%, respectively, and transformed unstable As/Cd to stable. The remediation mechanisms of MPCG on As included adsorption, oxidation, complexation and precipitation/co-precipitation. Meanwhile, the remediation mechanisms of MPCG for Cd included adsorption, ion exchange, complexation and precipitation. In addition, MPCG increases the abundance of sulfate-reducing bacteria (dsrA) by 43.39-381.28%, which can promote sulfate reduction. The sulfide can precipitate with As and Cd to reduce the availability of As and Cd in soil. Thus, MPCG is a promising amendment for achieving the remediation of As and Cd co-contaminated soil.

Techno-economic and environmental optimization of a combined regenerated gas turbine and supercritical CO2 cycle based on methane and hydrogen mixture as fuel for environmental remediation.

Achieving power generation systems with high efficiency and low emission of environmental pollutants is one of the requirements of a sustainable environment. In this study, a hybrid power generation system based on gas turbine (GT) with regenerator configuration is introduced. A supercritical carbon dioxide (sCO2) cycle is used to recover the waste heat from GT exhaust gases. In order to reduce the emission of environmental pollutants, the combination of hydrogen and methane is used as GT fuel. In order to investigate the effect of using hydrogen in the fuel composition, the fraction of hydrogen is changed between 0 and 50% and its effect on performance, environmental, and economic factors is investigated. Also, the effect of design parameters such as compressor pressure ratio (CPR) and turbine inlet temperature (TIT) of GT and sCO2 cycles on exergy efficiency, total cost rate (TCR), and normalized pollutants emission index are investigated. Then, by performing a bi-objective optimization process with the aim of achieving maximum exergy efficiency and minimum TCR, the optimal operating point is extracted. At the optimal operating point, exergy efficiency is 44% and TCR is 6 dollars/second.